Phone Repair Tools & Equipment

The tools, machines and materials I actually use every day in my repair shop in Belgrade — the same gear you've seen on my YouTube channel (103K+ subscribers). Everything is linked to Amazon so you can pick up the exact kit I recommend.

Affiliate disclosure: This page contains affiliate links. As an Amazon Associate I earn from qualifying purchases — at no extra cost to you. I only recommend tools I personally use or have tested in my own repair shop.

Phone Opening Tools

The exact tools I use to open iPhones and Samsung phones on the bench — without breaking glass or OLED.

QianLi 3D Screen Disassembler

Manual disassembler with chamfered blades that separates glued glass and digitizer cleanly. One of the tools I reach for on almost every screen job.

iFixit Pro Tech Toolkit

64-bit driver kit with tweezers, spudgers and a suction cup — the core kit on my workbench for every repair.

Kaisi Screen Opening Suction Kit

Suction-cup pliers kit that lifts glued screens and back glass without cracking them — strong grip, the opener I reach for first.

JAKEMY 145-in-1 Precision Screwdriver Set

Magnetized pentalobe, tri-point and Phillips bits covering every iPhone and Samsung screw I meet daily.

QianLi Ultra-Thin Pry Blade (i-Pry)

Ultra-thin spring-steel blade that slides under glued screens without cracking the OLED.

OCA Lamination & Refurbishing

OCA (Optically Clear Adhesive) machines and molds for rebonding glass to OLED panels — the heart of modern screen refurbishing.

TBK-568R LCD Separator

Heated separator for cleanly peeling broken glass off iPhone and Samsung OLED panels before re-laminating.

OCA Vacuum Autoclave (Bubble Remover)

Pressurized autoclave that cures OCA and clears micro-bubbles — non-negotiable for factory-grade refurbs.

OCA Adhesive Film Sheets (iPhone / Samsung)

250μm pre-cut OCA sheets in the sizes I use most — iPhone X through 15 Pro Max plus Galaxy S / Note.

YMJ Laminating Equipment

YMJ molds and presses make curved-edge Samsung and flat iPhone lamination repeatable — the alignment system behind clean, bubble-free glass refurbishing.

YMJ 7" Edge Laminator

The 7-inch edge laminator I use for Samsung Galaxy S / Note curved displays. Uniform pressure, no bubbles.

YMJ Laminating Mould Set (iPhone / Samsung)

Model-specific molds that hold each panel at the exact curvature during lamination — the key to a flush, factory-look screen.

YMJ Vacuum Laminating Machine

Compact vacuum laminator built around the YMJ mold system for fast, consistent OCA glass bonding.

Test & Diagnostic Equipment

Board-level diagnostic gear I reach for every day — power supplies, programmers and Face ID testers.

i2C Face ID Tester

Reads Face ID / dot-projector faults on iPhone X and newer. Tells you in seconds whether Face ID is repairable.

JCID V1SE Programmer

The programmer I use for battery, Face ID, True Tone and logic-board repairs on iPhone 6 through 15 Pro Max.

Adjustable DC Bench Power Supply (30V / 5A)

Adjustable 30V / 5A bench PSU with short-circuit protection — essential for diagnosing boot loops and shorts.

Fluke 117 Digital Multimeter

Industry-standard True-RMS multimeter. Used daily for continuity, diode and voltage checks on the board.

Adhesives, Glue & Tapes

Sealing phones properly matters. These are the exact adhesives I trust for daily repairs.

B-7000 Industrial Adhesive

Flexible, clear-drying glue — my go-to for frame seals, touch flex and small component bonding.

Tesa 61395 Double-Sided Tape

The thin, strong double-sided tape I use for OLED bonding and internal brackets. The pro standard.

OCA Sticker Assortment Pack

Multi-size OCA film sheets for common iPhone and Galaxy models — stock these in bulk if you repair daily.

Pre-cut Frame Adhesive Strips

Model-specific die-cut adhesive strips for a clean, factory-grade reassembly after repair.

Protection & Workbench

ESD, eye protection and a proper work surface — the basics that save boards, screens and eyes.

iFixit ESD Anti-Static Wrist Strap

Grounded wrist strap — cheap insurance against frying a logic board the moment you touch it.

Magnetic Silicone Repair Mat

Heat-resistant silicone mat with magnetic screw zones — the screw-tracking system I actually use.

UV-Blocking Laser Safety Glasses

Essential for UV glue curing and laser soldering — block 365/405nm UV from reaching your eyes.

Microscopes & Lighting

Board-level work is impossible without a good microscope and clean lighting.

AmScope SM-4TZ-144A Trinocular Microscope

3.5x–90x trinocular stereo zoom with a 144-LED ring — the exact microscope I use for board-level soldering.

AmScope 7X–45X Trinocular + Camera

7x–45x trinocular zoom with a USB camera — a solid starting point for board work before stepping up to the SM-4TZ.

AmScope 144-LED Ring Light

Dimmable 144-LED ring with four independent zones — clean, shadow-free light that makes flux and micro-traces pop.

"As an Amazon Associate I earn from qualifying purchases." Product availability, prices and specifications are set by Amazon and may change without notice. Viper Mobile doo — PIB: 112259884, Bulevar Arsenija Čarnojevića 91, stan 3, Belgrade.

Call now065/362-61-31